FantasticSearch | E-commerce Search Demo

Scroll to: Top Results

E-commerce Search Demo

AI Assisted Filters

Positive filters:

Negative filters:

Category filter:

Parameters

Query:

Positive filters:

Negative filters:

Category filters: All

AI Assist: ON

Page: 1

Products

Time taken: 3 Max score: 1000.000 Total hits: 600 Full time: 0.0 s
Showing 1-10 of 600 products

B004P8JQWG Price: $132.64 Score: 1000.000 Category: Tools Rating: 5 Votes: 4 Find similar products Cleveland 2075N Cobalt Steel Jobbers' Length Drill Bit, TiCN Coated, Round Shank, 135 Degree Notch Point, 1/8 (Pack of 10). The Cleveland 2075N Q-Cobalt wide land parabolic flute design, jobber length, high-speed steel (HSS) containing cobalt drill bit has a 38-degree helix angle, with a 135-degree notched-point drill point and Titanium carbonitride (TiCN) surface treatment, which is designed for high-performance drilling applications. The shank diameter is the same as the drill size. The 2075N series performs best when drilling into stainless steel, tool steel, low/med/high carbon steel, cast iron, aluminum, brass, plastic, and nickel alloys. TiCN is a ceramic coating that is harder than TiN and has lower friction. It combines toughness with good wear resistance. Once the coating has worn through, it can be replaced much easier than other coatings. Spiral flutes act as a passageway for chip extraction from the hole and for coolant to enter the hole. The twist of the flutes brings chips up and away from the cutting edge. The parabolic design allows for smooth and efficient chip, also called swarf evacuation. The higher, also called faster helix provides greater lifting power for chips and works well in deeper holes. The 135-degree notched-point drill point works well for hard and tough materials. The lip clearance is very shallow to provide support for the cutting edges. The shorter cutting edge reduces friction and heat during drilling, increasing tool life. The notched point can withstand higher thrust loads and has same benefits as a split-point design. The wider land increases the torsional strength of the drill. Round shanks allow use with a wide variety of tool holding systems. Made of cobalt-powder-metal substrate which is many times harder and stiffer than HSS, will hold an edge longer, and will deflect less than HSS. These are also more resistant to heat than HSS. These qualities allow it to run at higher speeds and feeds. They are made to ANSI and DIN industry standards, which help ensure that drill bits around the world, conform to the same specifications. The tolerances for various aspects of the Cleveland drill bits are: drill diameter range (inches) through 1/8 +0.0000/-0.0005, over 1/8 through 1/4 +0.0000/-0.0007, over 1/4 through 1/2 +0.0000/-0.0010, over 1/2 through 1 +0.0000/-0.0012, over 1 through 2 +0.0000/-0.0015, over 2 through 3 1/2 +0.0000/-0.0020; drill overall length and flute length #80 through 1/8 +0.1250/-0.0626, over 1/8 through 1/2 +0.1250/-0.1250, over 1/2 through 1 +0.2500/-0.1250, over 1 through 2 +0.2500/-0.2500, over 2 through 3 1/2 +0.3750/-0.3750; drill point angle diameter range (inches) 1/16 through 1/2 included angle (degrees) 118 or 135 +/-5 degrees, over 1/2 through 1 1/2 included angle (degrees) 118 +/-3 degrees, over 1 1/2 through 3 1/2 includes angle (degrees) 118 +/- 2 degrees; drill lip height diameter range (inches) 1/16 through 1/8 total indicator variation (inches) 0.0020, over 1/8 through 1/4 total indicator variation (inches) 0.0030, over 1/4 through 1/2 total indicator variation (inches) 0.0040, over 1/2 through 1 total indicator variation (inches) 0.0050, over 1 through 3 1/2 total indicator variation (inches) 0.0060. Drilling, or hole making, is the most common metalworking operation in the world. Twist drill bits are the most common type of drill bit used. Twist drill bits can be used in hand-operated drills, standalone drill presses, or a lathe. Greenfield Industries, which are a part of Top-Eastern Group, is one of the largest manufacturers of twist drills. They also manufacture cutting tools and related products under the following brands: Cleveland, Chicago-Latrobe, Cle-Line, Vermont Tap & Die, Bassett, Putnam Tools, Geo Met RJC, H & G, Vers-O-Tool, and Acme-Fette. The company has locations around the world, and provides tools adhering to ANSI, NAS, and DIN standards.	B007ITK12I Availability: Currently unavailable Score: 12.658 Category: Tools Rating: 4.6 Votes: 18 Find similar products 5/32-Inch Cobalt Drill Bit, 10 Pack, Jobber Length. OEM Tools 5/32 M-35 Cobalt Jobber length drill bits are designed for jobsite durability and extended life. Our web geometry has a thicker core than a standard drill bit, providing the user with maximum strength; helping eliminate side-load breakage. We added a unique parabolic flute that keeps the bit running cool. A standard 135 Split Point tip starts on contact; eliminating walking for fast accurate holes. Excellent for drilling on curved surfaces, requires less effort to drill and is highly recommended for use with portable drills. The Tri-Cut shank won't slip in the drill chuck. Bits above 3/8” diameter have a reduced shank diameter for use in 3/8 chucks. Applications include a variety of metals and synthetic materials. Performs best in steel, stainless steel, cast iron, titanium, nickel, and copper materials.
B001FB0M7O Price: $143.1 Score: 11.765 Category: Tools Rating: 3.4 Votes: 2 Find similar products Cleveland C00960 CLE-MAX 50 Piece High-Speed Steel General Purpose Jobber Length Drill Bit Set, Steam Oxide Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 1mm to 5.9mm Size. The Cleveland C00960 CLE-MAX jobber length drill bit set contains 50 high-speed steel drill bits in metric sizes 1 mm to 5.9 mm in 0.1 mm increments with a 118-degree conventional point for use in general-purpose applications. High-speed steel (HSS) provides hardness for wear resistance, and the steam oxide finish provides additional mild wear resistance. The round shank accommodates most drill chucks. The set comes in a metal index case with labeled compartments for identification and organization. Drill bits conform to Deutsches Institut für Normung DIN 338 standards. Drill bits are cutting tools used to make holes in a range of materials using machines such as handheld portable drills, machining centers, and lathes. Drill bits come in a variety of lengths and types, the most common of which is the twist drill bit. The round, twisted shaft of the twist drill bit typically has two cutting edges and flutes. The helical twist of the flutes brings chips up and away from the cutting edges and allows for coolant to reach the cutting edges. Jobber length twist drill bits, the most common length of twist drill bit, offer a good compromise of length and reach to work with the widest range of materials and applications. Mechanic's length twist drill bits (also called maintenance length) are a little shorter than jobber length and less prone to deflection when drilling. Short length twist drill bits (also called stub or screw-machine length) are the shortest and stiffest twist drill bits, helping to reduce the chance of deflection or breakage when drilling. Reduced shank drill bits (also called Silver and Deming drill bits) have a shank that is smaller in diameter than its shaft, permitting drilling machines with either a 1/2 or 3/4 drill chuck to create large holes. Long length twist drill bits (also called taper length) are a little longer than jobber length, allowing for deeper holes and longer reach. Extra long twist drill bits (also called extension) are longer than long length twist drill bits for greater reach or for drilling deeper holes. Cleveland manufactures tools for drilling, threading, and milling applications. The company, headquartered in Seneca, SC, meets International Organization for Standardization (ISO) standard 9001. What's in the Box? (50) drill bits, sizes 1 mm to 5.9 mm in 0.1 mm increments (50) drill bits, sizes 1 mm to 5.9 mm in 0.1 mm increments (1) metal case (1) metal case.	B00E4B17XK Price: $83.07 Score: 11.765 Category: Tools Rating: 5 Votes: 2 Find similar products Cleveland C72199 CLE-MAX 15 Piece High Speed Steel General Purpose Jobber Length Drill Bit Set, Uncoated (Bright) Finish, Round Shank, Spiral Flute, 118 Degrees Conventional Point, 1/16 to 1/2 Size. The Cleveland C72199 CLE-MAX jobber length drill bit set contains 15 uncoated (bright) high-speed steel drill bits in inch sizes 1/16 to 1/2 in 1/32 increments with a 118-degree conventional point for use in general-purpose applications. High-speed steel (HSS) provides hardness for wear resistance, and the uncoated finish has no additional surface treatment or coating. The round shank accommodates most drill chucks. The set comes in a metal index case with labeled compartments for identification and organization. Drill bits conform to American National Standards Institute (ANSI) standards. Drill bits are cutting tools used to make holes in a range of materials using machines such as handheld portable drills, machining centers, and lathes. Drill bits come in a variety of lengths and types, the most common of which is the twist drill bit. The round, twisted shaft of the twist drill bit typically has two cutting edges and flutes. The helical twist of the flutes brings chips up and away from the cutting edges and allows for coolant to reach the cutting edges. Jobber length twist drill bits, the most common length of twist drill bit, offer a good compromise of length and reach to work with the widest range of materials and applications. Mechanic's length twist drill bits (also called maintenance length) are a little shorter than jobber length and less prone to deflection when drilling. Short length twist drill bits (also called stub or screw-machine length) are the shortest and stiffest twist drill bits, helping to reduce the chance of deflection or breakage when drilling. Reduced shank drill bits (also called Silver and Deming drill bits) have a shank that is smaller in diameter than its shaft, permitting drilling machines with either a 1/2 or 3/4 drill chuck to create large holes. Long length twist drill bits (also called taper length) are a little longer than jobber length, allowing for deeper holes and longer reach. Extra long twist drill bits (also called extension) are longer than long length twist drill bits for greater reach or for drilling deeper holes. Cleveland manufactures tools for drilling, threading, and milling applications. The company, headquartered in Seneca, SC, meets International Organization for Standardization (ISO) standard 9001. What's in the Box? (15) drill bits, sizes 1/16 to 1/2 in 1/32 increments (15) drill bits, sizes 1/16 to 1/2 in 1/32 increments (1) metal case (1) metal case.
B00H7WCGGK Price: $51.69 Score: 11.494 Category: Tools Rating: 3.9 Votes: 21 Find similar products Drillco 1000EC Series Cobalt Steel Reduced-Shank Drill Bit, Bronze Finish, Round Shank with Flats, Spiral Flute, 135 Degree Split Point, 1 Size. The Drillco 1000EC series reduced-shank drill bit is made from cobalt steel with a bronze finish and has a 135-degree split point for use on tough, high-tensile strength metals. The reduced shank drill bit, also called a Silver and Deming drill bit, has a shank that is smaller in diameter than its shaft, permitting drilling with a 1/2 drill chuck. Cobalt steel provides extended tool life compared to high-speed steel drill bits, and maintains the tool's toughness and hardness in high drilling temperatures. The bronze finish lubricates the drill bit and provides wear resistance. The self-centering 135-degree split point penetrates hard material without a pilot hole and produces smaller chips that reduce clogging compared to a 118-degree point. The round shank with flats ground onto three sides reduces slippage of the bit when used in drill chucks. The drill bit conforms to American National Standards Institute (ANSI) specifications. Drill bits are cutting tools used to make holes in a range of materials using machines such as handheld portable drills, machining centers, and lathes. Drill bits come in a variety of lengths and types, the most common of which is the twist drill bit. The round, twisted shaft of the twist drill bit typically has two cutting edges and flutes. The helical twist of the flutes brings chips up and away from the cutting edges and allows for coolant to reach the cutting edges. Jobber length twist drill bits, the most common length of twist drill bit, offer a good compromise of length and reach for the widest range of materials and applications. Mechanic's length twist drill bits (also called maintenance length) are a little shorter than jobber length and less prone to deflection when drilling. Short length twist drill bits (also called stub or screw-machine length) are the shortest and stiffest twist drill bits, helping to reduce the chance of deflection or breakage when drilling. Reduced shank twist drill bits (also called Silver and Deming drill bits) have a shank that is smaller in diameter than its shaft, permitting drilling machines with a 1/4, 1/2, or 3/4 drill chuck to create large holes. Long length twist drill bits (also called taper length) are a little longer than jobber length, allowing for deeper holes and longer reach. Extra-long length twist drill bits (also called extension) are longer than long length twist drill bits for greater reach or for drilling deeper holes. Drillco manufactures cutting tools such as drill bits, reamers, taps, dies, annular cutters, end mills, and burs. The company, founded in 1978, is headquartered in Baton Rouge, LA.	B01E0WEB4O Price: $12.6 Score: 11.111 Category: Tools Rating: 3.9 Votes: 6 Find similar products Drill America - D/ASP43P12#43 High Speed Steel Split Point Drill Bit (Pack of 12), D/ASP Series. Drill America D/ASP series high speed drill bit is manufactured to National Aerospace Standard 907. Ideal for portable or machine drilling of low tensile strength alloy materials. They have a black oxide surface treatment that is abrasion resistant, reduces chip welding and improves chip flow. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
B07CCB7YXD Availability: Currently unavailable Score: 10.989 Category: Tools Rating: 4.2 Votes: 67 Find similar products 7/32 HSS Jobber Length Twist Drill Bits, Split Point, Pack of 10 PCS, by LU&MA, General Purpose for Wood, Plastic, Metal. 10 PCS High Speed Steel Twist Drill Bit Set By LU&MA (For Wood Plastic Metal ) These bits are also suitable for drilling in wood and plastic and are ideal for commercial and residential applications. Specification: Material:4241 metal Packing: Plastic case Material:4241 metal Material:4241 metal Packing: Plastic case Packing: Plastic case Includes: 10 drill bits:7/32inch(5.5mm) 10 drill bits:7/32inch(5.5mm) 10 drill bits:7/32inch(5.5mm) Features: Drill bits are engineered with premium high-speed steel in a bright finish General purpose HSS wire gauge straight shank jobber length bits Each drill bit has a 118°split-point tip that's designed for general purpose applications Drill bits drill exact-sized holes for tapping applications Drill bits are engineered with premium high-speed steel in a bright finish Drill bits are engineered with premium high-speed steel in a bright finish General purpose HSS wire gauge straight shank jobber length bits General purpose HSS wire gauge straight shank jobber length bits Each drill bit has a 118°split-point tip that's designed for general purpose applications Each drill bit has a 118°split-point tip that's designed for general purpose applications Drill bits drill exact-sized holes for tapping applications Drill bits drill exact-sized holes for tapping applications Applications: Ideal for use when non-fractional-sized holes are required For automotive, maintenance and repair, portable drills and stationary drill press applications Use in wood, metal and plastic etc Suitable for most power tools，like Bosch GBM350RE,etc Ideal for use when non-fractional-sized holes are required Ideal for use when non-fractional-sized holes are required For automotive, maintenance and repair, portable drills and stationary drill press applications For automotive, maintenance and repair, portable drills and stationary drill press applications Use in wood, metal and plastic etc Use in wood, metal and plastic etc Suitable for most power tools，like Bosch GBM350RE,etc Suitable for most power tools，like Bosch GBM350RE,etc Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. At the trepanning, please wear good protective measures, in case of chips splash damage eyes. Due to the difference between different monitors, the picture may not reflect the actual color of the item. Due to the difference between different monitors, the picture may not reflect the actual color of the item. At the trepanning, please wear good protective measures, in case of chips splash damage eyes. At the trepanning, please wear good protective measures, in case of chips splash damage eyes.	B0156DL36U Price: $20.85 Score: 10.989 Category: Tools Rating: 3 Votes: 2 Find similar products YG-1 DLGP Gold-P High Speed Steel Jobber Drill Bit, TiN Finish, Straight Shank, Parabolic Spiral, 130 Degree, 1/4 Diameter x 4 Length (Pack of 10). The Gold-P drill has a full thickness tin coating on its tip. This allows higher production rates and lower costs. The newly designed point, helps reduce thrust and is self centering. Jobber length, gold-p coated. Right hand spiral and parabolic flute. Bright body TiN coating on working part. Applicable for improved chip removal in most materials, especially in deep drilling applications. ANSI Specifications met.
B00FXI8538 Price: $12.22 Score: 10.870 Category: Tools Rating: 5 Votes: 2 Find similar products Drill America - DWDNVP6 V High Speed Steel Black Oxide Drill Bit (Pack of 6), DWDN Series. Drill America black oxide series high speed drill bit is a dependable, general purpose drill designed to perform in a broad range of materials in the iron and steel families. Ideal for production, maintenance or portable drilling jobs. Surface treated with abrasion-resistant black oxide.Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. Round shanks allow use with a wide var.	B003JTI5LK Availability: Currently unavailable Score: 10.870 Category: Tools Rating: 5 Votes: 2 Find similar products Precision Twist C29HX10 High Speed Steel Jobber Length Drill Bit Set, Purple and Gold Oxide Finish, 135 Degree Point, Inch, 29 Piece, 1/16 to 1/2 x 64ths. This Precision Twist C29HX10 jobber length drill bit set contains 29 high-speed steel drill bits, including inch sizes 1/16 through 1/2 in 1/64 increments, with a purple and gold oxide finish and a 135-degree split point for general-purpose applications on a range of materials. High-speed steel (HSS) provides hardness for wear resistance, and the purple and gold oxide finish provides additional wear resistance compared to an uncoated drill bit. Compared to standard drill bits, these tools have a thicker web for increased strength and rigidity. The self-centering 135-degree split point penetrates hard material without a pilot hole and produces smaller chips, which are less likely to clog a hole than a 118-degree point. These jobber length drill bits have a drilling depth up to four times their diameter. The round shank accommodates most drill chucks. The set comes in a metal index case with labeled compartments for identification and organization. Drill bits conform to American National Standards Institute (ANSI) standards. Drill bits are cutting tools used to make holes in a range of materials using machines such as handheld portable drills, machining centers, and lathes. Drill bits come in a variety of lengths and types, the most common of which is the twist drill bit. The round, twisted shaft of the twist drill bit typically has two cutting edges and flutes. The helical twist of the flutes brings chips up and away from the cutting edges and allows for coolant to reach the cutting edges. Jobber length twist drill bits, the most common length of twist drill bit, offer a good compromise of length and reach to work with the widest range of materials and applications. Mechanic's length twist drill bits (also called maintenance length) are a little shorter than jobber length and less prone to deflection when drilling. Short length twist drill bits (also called stub or screw-machine length) are the shortest and stiffest twist drill bits, helping to reduce the chance of deflection or breakage when drilling. Reduced shank drill bits (also called Silver and Deming drill bits) have a shank that is smaller in diameter than its shaft, permitting drilling machines with either a 1/2 or 3/4 drill chuck to create large holes. Long length twist drill bits (also called taper length) are a little longer than jobber length, allowing for deeper holes and longer reach. Extra long twist drill bits (also called extension) are longer than long length twist drill bits for greater reach or for drilling deeper holes. Dormer Pramet manufactures cutting tools under the following brands: Precision Twist Drill, Dormer, Union Butterfield and Pramet. The company has locations around the world, and provides tools adhering to ANSI, NAS, and DIN standards. What’s in the Box? 29 drill bits, inch sizes 1/16 through 1/2 in 1/64 increments 29 drill bits, inch sizes 1/16 through 1/2 in 1/64 increments Plastic case Plastic case.