FantasticSearch | E-commerce Search Demo

Scroll to: Top Results

E-commerce Search Demo

AI Assisted Filters

Positive filters:

Negative filters:

Category filter:

Parameters

Query:

Positive filters:

Negative filters:

Category filters: All

AI Assist: ON

Page: 1

Products

Time taken: 2 Max score: 1000.000 Total hits: 100 Full time: 0.0 s
Showing 1-10 of 100 products

B014KRGE12 Availability: Currently unavailable Score: 1000.000 Category: Electronics Rating: 3.7 Votes: 14 Find similar products SunFounder AD/DA Converter PCF8591 Sensor Module Compatible with Arduino and Raspberry Pi. .	B076Q1QKSX Availability: Currently unavailable Score: 7.463 Category: Electronics Rating: 3.8 Votes: 7 Find similar products WINOGNEER Serial Port Expansion Board RS232 for Pi 3 Model B 2 B B+ GPIO UART Shield with IR Receive. Description: 1. Expansion board size: 65mm * 56.5mm, the standard Pi HAT extension plate size2. Power indicator3. Infrared receiver function4. GPIO extended function: A. Up to 16 independently with power and ground GPIO (3.3V level), and provide a corresponding relationship table, at a glance B. Two independent SPI extended interface with 1 I2C extended interface C.One RS232 standard serial port, can be directly connected to the PC etc. Package Included: 1 x WINGONEER GPIO Serial Port Expansion Board.
B08V4X5L5B Price: $16.59 Score: 7.353 Category: Electronics Rating: 4.3 Votes: 17 Find similar products ACEIRMC 6pcs INA219 I2C Bi-Directional DC Current Power Supply Sensor Breakout Module Compatible with Arduino Raspberry Pi. .	B01I92B5W2 Price: $8.99 Score: 7.246 Category: Electronics Rating: 4 Votes: 1 Find similar products TOLAKO GPIO Module with Dual Channel Digital I/O Ports for Arduino. Package included: 1X GPIO Module.
B00FAQSMR2 Price: $14.99 Score: 6.993 Category: Electronics Rating: 5 Votes: 4 Find similar products FTDI USB to Serial Breakout Board - Three Pack of The VisiPort2. Designed, Assembled, Tested and Distributed in the USAThis item includes three VisiPortsThe VisiPort2 is a USB To Serial Module that has been designed to program Arduinos. Its small size allows it to fit into bread board where other programmers are too big and bulky. It is designed to program Arduinos. Its six pin female header connects easily to a Mini Pro with no bread board needed. It has one green LED that indicates power is applied to the FTDI chip. There are two amber LEDs to indicate when Tx and Rx are active. The VisiPort2 works with 5Volt and 3.3Volt Arduinos Use the three pin jumper in the upper right corner to select I/O voltage of the VisiPort2. This selection allows compatibility with all Arduinos. The VisiPort2 Uses a Micro USB Connector The Micro USB connector is lower profile and allows cables to connect into the center of the VisiPort2. This keeps the overall size smaller than any other programmer. The VisiPort2 has a Flexible Arduino Reset We gave the VisiPort2 jumper selectable DTR or RTS reset capability.	B007IZJZ24 Availability: Currently unavailable Score: 6.757 Category: Electronics Rating: 3 Votes: 1 Find similar products Somfy Z-Wave to Digital Motor Interface (1870171). Converts Z-Wave commands to Somfy motor control commands Enables Z-Wave control of Sonesse 50 ILT and Sonesse 30 RS-485 motors Accepts commands from Z-Wave remotes, wall switches, etc.
B00SCJNV7K Availability: Currently unavailable Score: 6.757 Category: Electronics Rating: 5 Votes: 2 Find similar products Micro SD Storage Board TF Card Memory Shield Module SPI For Arduino. Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the Micro SD card read and write files. Users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Support Micro SD Card, Micro SDHC card (high-speed card) The level conversion circuit board that can interface level is 5V or 3.3V Communication interface is a standard SPI interface Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply; Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal; Micro SD card connector: yes since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, easy to install positioning, to achieve inter-module combination; Specifications: Power supply:4.5V - 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size:45 x 28mm Net weight:6g Package Includes 1 x shield module.	B01KOMED8S Availability: Currently unavailable Score: 6.757 Category: Electronics Rating: 3.5 Votes: 2 Find similar products FTDI FT232RL USB to TTL Serial Adapter 3.3V/5V switch selectable logic levels. .
B00RBHOBJG Availability: Currently unavailable Score: 6.757 Category: Electronics Rating: 4 Votes: 2 Find similar products Gikfun USB to RS485 TTL Serial Converter Adapter for Arduino EK1192. USB to RS485 TTL Serial Converter Adapter FTDI interface FT232RL 75176 Module.	B00ATRDOHU Availability: Currently unavailable Score: 6.667 Category: Electronics Rating: 3.5 Votes: 2 Find similar products SD Shield for Arduino. SD card shield for Arduino. Supports SD and MicroSD cards (on board switch to toggle between them). Header connectors must be soldered. Compatible with standard SD card libraries. Make sure you set CS to pin 10. Contact us at ManyLabs if you have troubles.