FantasticSearch | E-commerce Search Demo

Scroll to: Top Results

E-commerce Search Demo

AI Assisted Filters

Positive filters:

Negative filters:

Category filter:

Parameters

Query:

Positive filters:

Negative filters:

Category filters: All

AI Assist: ON

Page: 1

Products

Time taken: 3 Max score: 1000.000 Total hits: 600 Full time: 0.0 s
Showing 1-10 of 600 products

B075G9NPWW Price: $11.99 Score: 1000.000 Category: Tools Rating: 3.7 Votes: 24 Find similar products LM YN ZVS Driver Board ZVS Induction Heating Circuit DC12-30V Zero Voltage Switch Power Supply Driver Board. Working voltage: DC12V-30V (less than 12V does not work) Power Requirements: Voltage = 12V, Current ≥ 5A ; Voltage ≥ 24V, Current ≥ 10A (the greater the current, the more adequate power); Operating frequency: 30kHz-50kHz, adaptive. Output Voltage / Power: Input 12V / 5A, the output of about 10000V / 60W; Input 24V / 10A, the output of about 20000V / 200W. Arc length: 1-5cm; Power range: 180-360W; Size: 75 * 70.6mm (L * W); Package Included: 1*ZVS Driver Board ZVS Induction Heating Circuit DC12-30V Zero Voltage Switch Power Supply Driver Board.	B072Z628LP Price: $11.99 Score: 8.000 Category: Tools Rating: 3.5 Votes: 7 Find similar products LM YN 1-Channel Solid State Relay Module High-low Level Trigger 3A Optocoupler Isolation. Feature: 1, DC 5-32V wide voltage power supply, with anti-reverse power supply capacity; 2, the output rated load: AC / DC 0-50V / 2A; maximum load: AC / DC 0-60V / 3A (within 100ms); 3, the output port is normally open type of switch contacts, the contact is not charged node, the current direction without requirements; 4, the input control high and low selectable; built-in current limiting resistor, you can directly use the power of the positive or negative control, you can also use the microcontroller I / O port control; 5, the module anti-interference ability, stable performance; trigger current minimum 0.1mA; 6, with power indicator (red) and each way relay status indicator (blue) 7, the use of blue terminals; 8, module size: 5.0cm * 3.0m * 1.0cm (L * W * H) Precautions: This module can be used directly for signal or resistive load control; If you are using control for inductive loads (eg small motors, solenoid valves, etc.), keep more than 3 times the remaining amount and add freewheeling diodes at both ends of the inductive load. Module control : 1. DC+ : Positive DC power supply; 2, DC-: DC power supply negative; (DC5-32V). 3, XM: Trigger side COM port, can choose high level or low level to trigger through this interface. 4. X1: trigger terminal, can choose high level or low level trigger, trigger current only needs 0.1mA. Low-level trigger: XM connected to positive, X1 input 0-2V; High-level trigger: XM connected to negative , X1 input 3-32V; Relay output: 1, NO1: relay normally open interface; 2, C0M1: relay common interface; Package Included: 1*1-Channel Solid State Relay Module If you for any reason are not happy with any product supplied , please do not hesitate to contact us and we will do our best to solve your problem .
B08THVDBRX Availability: Currently unavailable Score: 7.752 Category: Tools Rating: 3.5 Votes: 26 Find similar products Teyleten Robot ZVS DC12-30V 1000W 20A Low Voltage Induction Board Heating Driver Board Module. .	B00CSM2R22 Availability: Currently unavailable Score: 7.692 Category: Tools Rating: 3 Votes: 14 Find similar products HY CNC Single Axis TB6600 0.2 - 5A Two Phase Hybrid Stepper Motor Driver Controller. This item is a high performance micro-stepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Moreover, the brand new design with BiCD0.13 (50V) process technology on the chipset also ensures maximum 5.0A output current and 50V output withstand voltage. Consequently, as long as the current range of the stepper motor is within 0.2-5 amps, all the 2 Phase or 4 Phase of Nema17, Nema23, Nema24 and Nema34 stepper motors will work perfectly with this new-type TB6600HG Stepper Driver - average current control, two-phase sinusoidal current drive output - DC 12 ~ 48V power supply, the internal integration of 12V and 5V regulator - optically isolated signal input / output - overvoltage, undervoltage, overcurrent, and white short-circuit protection - Input voltage DC 12 ~ 48V input - The input current of 1 to 5 amps, select the drive a stepper motor. - Output current of 0.2A ~ 5A - Temperature Operating Temperature -10 to 45 C; Storage temperature -40C to 70C - Humidity not condensing, not drops - Gas prohibit combustible gas and conductive dust - Weight 200 grams.
B00AJGM37I Availability: Currently unavailable Score: 7.692 Category: Tools Rating: 4.2 Votes: 265 Find similar products L298N H-bridge Motor Controller, DROK L298N Motor Driver Board DC Dual H Bridge Robot Stepper Motor Regulator and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove. Parameter: Chip: L298N Logic voltage: 5V Logic current 0mA-36mA Storage Temperature: -20 ℃ to ℃ to +135 Operating mode: H-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single bridge) Maximum power: 25W Dimensions: 43x43x27mm Product features: 1. L298N as main driver chip makes strong driving ability/small heating/strong anti-interference 2. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability 3. This moduel integrated with one internal 5V power supply, meaning when your driving voltage is 7V-35V, it makes 5V of energy board power supply logically; when 5V of energy board power on, please not input voltage to +5V power supply in interface but you can lead 5V voltage for external usage Eg: ENA enable IN1 IN2 to control OUT1 OUT2 ENB enable IN3 IN4 to control OUT3 OUT4 Package includes: 1x L298N Module.	B01GPMAR5Y Price: $15.99 Score: 7.634 Category: Tools Rating: 3.6 Votes: 14 Find similar products KNACRO pwm Speed Controller PWM Electronic Governor 40A DC 10V-50V 12V / 24V / 36V / 48V Brushed DC Motor Controller Maximum Power of 2000W Third Gear Forward/Reverse/Stop. Input voltage: DC10-50V.Output voltage: Load Linear. Input Current: require large than the motor operating current.Output Current: determine load size. Continuous current: 40A within.Maximum power: 2000W.Knob hole: 7mm. Speed type: modulated current.Speed mode: ON \ OFF linear potentiometer 270 degrees.Speed range: 0-100%. Operating frequency: 25KHZ.Forward Reverse: Support. Input voltage: DC10-50V. Output voltage: Load Linear. Input Current: require large than the motor operating current. Output Current: determine load size. Continuous current: 40A within. Maximum power: 2000W . Knob hole: 7mm. Speed type: modulated current. Speed mode: ON \ OFF linear potentiometer 270 degrees. Speed range: 0-100%. Operating frequency: 25KHZ. Forward Reverse: Support. Size: 100 * 76 * 28 mm（LWH）. Weight: 180g.
B08DRC5M93 Price: $9.79 Score: 7.634 Category: Tools Rating: 5 Votes: 1 Find similar products 20W Driver Power. Description: - Energysaving ; High efficiency - Good Radiating and - A necessary part for s - Made of high quality material, practical and durable - Power Supply,Widely used in Industrial automation, LED display, communications, etcSpecification: - Case Material: Metal - Size: Approx. 78x 30x 23 mm/ 3.07x 1.18x0.91 inch - Color: As pictures show - Input voltage: AC85265V/ / 5060HZ - Output voltage: DC 2038V - Current: 600mA ±5% - Tc:75°C - Ta：50°C（max） - Power: 20WPackage Includes:1 piece LED Driver 20WNote:Please allow slight dimension difference due to different manual measurement.	B07KWNH2ZJ Price: $13.89 Score: 7.407 Category: Tools Rating: 4.2 Votes: 46 Find similar products Yosoo 5V-12V ZVS Low Voltage Heating Power Supply Module,Induction Power Heating Supply Module,with Heating Coil Power Supply. .
B07QLZRRCD Price: $120.89 Score: 7.143 Category: Tools Rating: 2.7 Votes: 4 Find similar products 220V 1.5kW Variable Frequency Driver,Single Phase Input and 3 Phase Output VFD Inverter,Built-in PID Control Function, Multiple Fault Protection,for Engraving Equipment, Mechanical Equipment. 220V 1.5kW Variable Frequency Driver,Single Phase Input and 3 Phase Output VFD Inverter,Built-in PID Control Function, Multiple Fault Protection,for Engraving Equipment, Mechanical Equipment Features: 1. Control method: V/F control and . 2. Frequency setting method: digital setting, analog setting, serial communication setting, PID setting, etc. 3. Built-in PID control function to conveniently constitute a simple automatic control system. 4. Built-in simple PLC and 6 multi-function input terminals to achieve running state, zero speed, calculator, external exception program running and other indications and alarms. 5. Other functions: Deceleration stop or free stop, DC brake, automatic reset and restart, PLC program control, etc. 6. Provide a variety of fault protection functions including overcurrent, overvoltage, undervoltage, over temperature, phase loss and overload. 7. Applicable for fan pump, engraving equipment, mechanical equipment, textile equipment, electrical equipment, CNC equipment and so on. Specification: Model: V8M2S1R5GB Application range: Universal Supply voltage: Low voltage Input voltage: 1-phase AC 220V Output voltage: 3-phase AC 0-220V Output current: 7A Suitable motor power: 1.5kW Dimensions: 14797133mm / 5.83.84.4in Weight: Approx. 1409g/49.7oz Package list: 1 x Frequency Inverter Note: 1. Due to the difference between monitors and light effects, the pictures may not reflect the actual color of the item. 2. Please allow slight error due to manual measurement. Thanks for your understanding. 220V 1.5kW Variable Frequency Driver,Single Phase Input and 3 Phase Output VFD Inverter,Built-in PID Control Function, Multiple Fault Protection,for Engraving Equipment, Mechanical Equipment.	B07R52TZFJ Availability: Currently unavailable Score: 6.993 Category: Tools Rating: 3.9 Votes: 5 Find similar products tatoko DC Speed Controller, DC 12-48V 20A DC Motor Controller, Universal 0.01-1000W 16kHz PWM Stepless Brushed Motor Control, Variable Speed Control Generator Kit with Output Voltage LED Display. A. The input of the DC motor speed regulator must be DC input, cannot be connected to AC input otherwise, the motor speed regulator will be burnt. B. The positive side and the negative side of DC power supply cannot be reversed connected, or the motor speed regulator will be damaged. B. The positive side and the negative side of DC power supply cannot be reversed connected, or the motor speed regulator will be damaged. C. Adjusting the potentiometer knob can change the duty ratio of the output of the motor speed regulator, and then change the speed of the motor. C. Adjusting the potentiometer knob can change the duty ratio of the output of the motor speed regulator, and then change the speed of the motor. Note: This variable voltage and speed controller is for brushed dc motor, not suitable for brushless motor. Note: This variable voltage and speed controller is for brushed dc motor, not suitable for brushless motor. Wide voltage Range: from DC 12V to 48V Wide voltage Range: from DC 12V to 48V The maximum current can reach 20A ,suggest within10A for use. The maximum current can reach 20A ,suggest within10A for use.