FantasticSearch | E-commerce Search Demo

Scroll to: Top Results

E-commerce Search Demo

AI Assisted Filters

Positive filters:

Negative filters:

Category filter:

Parameters

Query:

Positive filters:

Negative filters:

Category filters: All

AI Assist: ON

Page: 1

Products

Time taken: 3 Max score: 1000.000 Total hits: 600 Full time: 0.0 s
Showing 1-10 of 600 products

B07RQ9PGBR Availability: Currently unavailable Score: 1000.000 Category: Tools Rating: 1 Votes: 1 Find similar products ERICO CADWELD Plus 45PLUSF20 Welding Material, Copper Oxide/Aluminum, Light Blue. ERICO CADWELD PLUS Welding Material, Copper Oxide/Aluminum, Light Blue.	B00597TWOO Price: $97.18 Score: 6.098 Category: Tools Rating: 5 Votes: 1 Find similar products Weldcote 45CF 1/16 x 3 troy oz coil Cadmium Free. WELDCOTE 45CF is a general purpose silver brazing alloy with a wide melting range and widely used in many brazing operations. WELDCOTE 45CF is commonly used to join any combinations of copper , brass , steel and bronze. Package of 1.
B0779PYKTN Availability: Currently unavailable Score: 5.917 Category: Tools Rating: 4.3 Votes: 17 Find similar products EFeMn-A - Hardfacing Low Hidrogen High Manganese Electrode - D256 - AWS 5.13-14 x 1/8 - (11 LBS). Introduction: D256 is a high manganese steel surfacing electrode with low hydrogen potassium type coating AC/DC. (When AC welding, Open circuit (no load) voltages of arc welding should be higher than 70V). When surfacing use low current, narrow bead, hammer or water quench immediately when hot to reduce crack tendency. Use in austenitic high manganese steel Recommendations for welding: Austenitic manganese steels, in as cast condition or as weld metal, are sensitive to hot shortness and may crack if subjected to excessive heat. Under normal conditions the base material should not be preheated and interpass temperatures above 200 °C should be avoided. Welding outdoor in very cold weather, the base material should be warmed up to 50-100 °C. Weld metal hardness, (all weld metal): As welded....180-200 HB. (no preheat, interpass temperature 100-150 °C.) Work hardened...44-48 HRC. (About 25 % degree of reduction.) Machinability: Grinding is normally applied. Overheating must be avoided. Redrying the electrodes: 200 °C, 2 h.	B006W4QU20 Price: $12.99 Score: 5.814 Category: Tools Rating: 4.5 Votes: 89 Find similar products Hobart H119916-R01 1-Pound Plastic 7018 Stick Welding Electrode, 1/16-Inch. From the Manufacturer 7018 Welding Electrodes - Size 1/16 - 1LB. A low-hydrogen electrode for use in all positions on low, medium and high-carbon steels. 70,000 PSI tensile strength. Ideal for out-of-position welding and tacking. Runs on AC or DCEP (reverse) polarity. Not recommended for low-voltage AC welders.
B07K2Z8KH2 Availability: Currently unavailable Score: 5.814 Category: Tools Rating: 1 Votes: 1 Find similar products Dabixx 2.00mm3m Copper Aluminum cored Wire Low Temperature Aluminium Welding Rod. Features: 1. Welding effect is good: its welding effect is full, smooth! With the help of internal powder. With low melting point, good fluidity, hardness and toughness, good sealing. Do not have to use other flux powder 2. Direct use: do need any flux poweder, open package that is used! Very convenient! Easy to weld. 3. Welding: firsst use sandpaper to polish brass and aluminum tube welding parts (must to clean metal surface's paint, oxide, oil, etc), moving the gun to be heated evenly welding parts, and then continue to use the electrode to be welded When the temperature rises to 360 degrees, the copper and aluminum welding rod to melt and evenly into the joint, Remove the torch after the weld is full , waiting cooling is OK. No further treatment after cooling, flux residue is visible but not corrosive, non-hygroscopic and firmly attached. Suitable for: 1, transformers and reactors' aluminum and copper joints' copper and aluminum foil's welding 2, refrigerator and air conditioning's condenser / evaporator's aluminum pipe and brass's welding; 3, radiators, motors, batteries, household appliances and other products' copper and aluminum wire's welding. Specifications: Products name: Copper aluminum flux cored wire Diameter: 2.00mm*3m Length: 3m Note: Please allow 1-3cm error due to manual measurement.pls make sure you do not mind before you bid Due to the difference between different monitors, the picture may not reflect the actual color of the item.Thank you!.	B07NTPDFWX Price: $18.99 Score: 5.747 Category: Tools Rating: 4.3 Votes: 109 Find similar products Eastwood 30/70 Body Solder Stick 1/4 lb Car Care Auto Brass Welding Rods Wires Body Repair Tin - Lead Alloy Heat Control. .
B07JGSNNYR Price: $12.49 Score: 5.747 Category: Tools Rating: 3.7 Votes: 5 Find similar products Chip Quik RASWLF.020 2OZ LF Solder Wire 96.5/3/0.5 Tin/Silver/Copper Rosin Activated .020 2oz. LF Solder Wire 96.5/3/0.5 Tin/Silver/Copper Rosin Activated .020 2oz.	B00A4KXGP2 Availability: Currently unavailable Score: 5.682 Category: Tools Rating: 5 Votes: 1 Find similar products Rosin Core Solder, Dia 0.062 in, 1lb. ' Leaded Rosin Core Solder, Contents 40 Percent Tin, 60 Percent Lead, Rosin Core, Container Size 1 lb., Container Type Spool, Used For Speaker Wire, Motors, Appliances and General Wiring, ASTM B-32 '.
B00406SQJ2 Price: $55.03 Score: 5.682 Category: Tools Rating: 4.2 Votes: 4 Find similar products HARRIS 00SIBF2 SIB Welding Wire, 0.035 x 2 lb. Spool. This copper-silicone alloy is used to weld similar composition base metals, brass and to weld these copper alloys to steel. Silicon bronze is also frequently used in GMAW braze welding of coated sheet steels.	B008BJDQYO Availability: Currently unavailable Score: 5.682 Category: Tools Rating: 5 Votes: 1 Find similar products HARRIS 80SD250 Welding Wire, ER80SD-2, 3/32 x 36 MS, 10 lb. Package. Contains a high level of deoxidizers (Mn and Si), also Molybdenum for increase strength. Suitable for single and multi-pass welding of a variety of carbon and low alloy steels.