FantasticSearch | E-commerce Search Demo

Scroll to: Top Results

E-commerce Search Demo

AI Assisted Filters

Positive filters:

Negative filters:

Category filter:

Parameters

Query:

Positive filters:

Negative filters:

Category filters: All

AI Assist: ON

Page: 1

Products

Time taken: 2 Max score: 1000.000 Total hits: 100 Full time: 0.0 s
Showing 1-10 of 100 products

B08HMGXBZ4 Price: $19.99 Score: 1000.000 Category: Electronics Rating: 4.4 Votes: 35 Find similar products BS-280 GPS Module Glonass Module Navigation RS-232 Level (Arduino GPS, Drone Microcontroller GPS Receiver) for 51 Microcontroller STM32 Arduino UNO R3 with IPEX Antenna High Sensitivity. Product Advantages: This GPS moduel has 4M FLASH, can store the configuration permanently. Small size, low power consumption and high ensitivity makes diy possible Electrical Characteristics: Chipset: G7020-KT Frequency: GPS L1, SBAS L1, QZSS L1 Receiving Format: GPS, SBAS, QZSS Channels: 56 Searching Channel Sensitivity: Tracking: -162dBm Reacquisition: -160dBm Cold Start: -148dBm Accuracy: Position Horizontal:2.0 m (Typical Open Sky) Velocity: 0.1m/sec 95% (SA off) Timing: 1us synchronized to GPS time Acquisition Time: Cold Start: 29s Warm Start: 25s Hot Start: 1s Data Output: Support Rate: 4800bps to 921600bps, Default 9600bps Data Level: TTL Level Data Protocol: NMEA-0183 NMEA Message: RMC, VTG, GGA, GSA, GSV, GLL Update Rate:1Hz-10Hz, Default 1Hz FLASH: 4M FLASH, Store the configuration permanently Operational Limits: Altitude: <50,000m Velocity: <515m/s Acceleration: <4g Power Consumption: VCC: DC Voltage 3.6V-5.5V, Typical: 5.0V Current: Capture 45mA/5.0V Built-in LED: TX LED: blue. The data output, TX LED flashing PPS LED: red. PPS LED not bright when GPS not fixed, flashing when fixed Specifications: Dimension: 28mm28mm8mm Weight: 11.5g \ Connector:1.25mm 6pins connector Environment: Operating Temp: -40 °C ~ +85°C Storage Temp: -40°C ~ +105°C Application areas: Vehicle-mounted Handheld devices such as PDAs Vehicle monitoring Mobile phones, camcorders and other mobile positioning systems Sharing bike Sharing mobile power. Package Including 1 * GPS Module with Built-in Antenna.	B07KPMK8VX Availability: Currently unavailable Score: 6.897 Category: Electronics Rating: 2 Votes: 1 Find similar products STLINK-V3 Modular in-Circuit debugger and Programmer for STM32/STM8. The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board. The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board. The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and bridge interfaces (SPI, I2C, CAN, GPIOs) allowing for instance the programming of the target through bootloader. The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board. Key Features: Stand-alone probe with modular extensions Self-powered through a USB connector (Micro-B) USB 2.0 high-speed compatible interface Direct firmware update support (DFU) JTAG / serial wire debugging (SWD) specific features: 3 V to 3.6 V application voltage support and 5 V tolerant inputs, Flat cables STDC14 to MIPI10 / STDC14 / MIPI20 (connectors with 1.27 mm pitch), JTAG communication support, SWD and serial wire viewer (SWV) communication support SWIM specific features (only available with adapter board MB1440): 1.65 V to 5.5 V application voltage support, SWIM header (2.54 mm pitch), SWIM low-speed and high-speed modes support Virtual COM port (VCP) specific features: 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs, VCP frequency up to 15 MHz, Available on STDC14 debug connector (not available on MIPI10) Multi-path bridge USB to SPI/UART/I2C/CAN/GPIOs specific features: 3 V to 3.6 V application voltage support and 5 V tolerant inputs, Signals available on adapter board only (MB1440) Drag-and-drop Flash programming Two color LEDs: communication, power.
B01D45YCW4 Price: $32 Score: 6.897 Category: Electronics Rating: 4.8 Votes: 32 Find similar products Electronics-Salon DIN Rail Mount Screw Terminal Block Adapter Module, for Raspberry Pi A+ 3A+ B+ 2B, 3B 3B+ 4B Zero Zero-W. DIN Rail Mount Screw Terminal Block Adapter Module. With the adapter module you can easily extend Raspberry-Pi projects to industrial control applications. Applications for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B Zero Zero-W (Now upgraded to Version 1.2, to add support Pi Zero and Pi Zero W. But, you must soldered a 2x20pins male header in your Raspberry Pi ZERO). CN3 and CN4 1:1 on board connected. CN3 connect Raspberry Pi board. CN4 Extension connector, you can use a FRC 40-pins wire connect to other devices. Pitch 3.81mm/0.15 high quality screw terminal block, wire range 26-16AWG, strip length 5mm, Metric M2 slotted screw. FR-4 fiber glass PCB, dual copper layers. Fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail, and the carrier can be taken apart for panel mount use. Module Dimensions: L 102mm x W 87mm x H 45.5mm, PCB Dimensions: L 100mm x W 72.5mm. Note: the item not include Raspberry-Pi module.	B0B9XPFLR7 Price: $69.98 Score: 6.849 Category: Electronics Rating: 1 Votes: 1 Find similar products GPS Module FS-IBG01 Support GPS Beidou Satellite Dual Satellite System Positioning for RC Car RC Boat. Flysky GPS Module FS-IBG01 Support GPS Beidou Satellite Dual Satellite System for RC Car RC Boat Features: 1. Supports multiple satellite systems such as GPS and Beidou, and has the characteristics of high sensitivity, short acquisition time, strong anti-interference ability and low power consumption of the system. 2. In dual-mode mode, the speed measurement accuracy is 0.05m/s, and the positioning accuracy is better than 0.5m. 3. Rich usage scenarios: support cars, ships, airplanes, robots, etc. 4. Tracking: -167dBm.Capture: -160d Bm. Cold start: -148dBm.Warm start: -157dBm. Cold start time: average 26s.Hot start time: average 1s. Positioning accuracy: 0.3 degrees.Speed measurement accuracy: 0.05 m/s.Time Accuracy: RMS 99% 30ns. Maximum height: 50,000m.Acceleration: ?4g. 5. LED display: yes.Update frequency: 10Hz.Data format: i-BUS2. Input power: 3.5~9V/DC.Temperature range: -10??+60?.Humidity range: 20%?95%. Specification: Product model: FS-iBG01 Support satellite system: GPS, Beidou Compatible models: cars, ships, airplanes, robots, etc. Tracking: -167dBm Capture: -160d Bm Cold start: -148dBm Warm start: -157dBm Cold start time: average 26s Hot start time: average 1s Positioning accuracy: 0.3 degrees Speed measurement accuracy: 0.05 m/s Time Accuracy: RMS 99% 30ns Maximum height: 50,000m Acceleration: ?4g LED display: yes Update frequency: 10Hz Data format: i-BUS2 Input power: 3.5~9V/DC Temperature range: -10??+60? Humidity range: 20%?95% Dimensions: 40.240.218.5mm Body weight: 24.1g Appearance color: black Certification: CE, FCC.
B01N47LXRA Price: $9.19 Score: 6.849 Category: Electronics Rating: 4.3 Votes: 67 Find similar products HiLetgo 2pcs CP2102 MICRO USB to UART TTL Module 6 Pin Serial Converter STC Replace FT232. Description: 1. Original chip CP2102, generate COM port after installing the driver. 2. Then the standard input MICRO MINI-USB cable connected to the computer USB interface, with 3.3V and 5V two power output 3. With a resettable fuse. In the event of accidental short-circuit can effectively protect your device and computer USB port to download 4. On-board status indicators, receiving indicator properly installed drive status indicator remains, send and receive indicator flashes when the communication with run LED indicator. 5. Support baud rates from 300bps ~ 1Mbps between 6. The communication format support: 1) data bits 5,6,7,8; 2) support 1.5, 2 stop bits; 3) odd, even, mark, space, none parity 7. Supported operating systems: windows 8.1 / 7 / vista / xp / 98, Mac OS-X / OS-9, Linux 8. USB seat MICRO MINI-USB interface Block 9. Chip components for the regular company of welding, stable quality, beautiful appearance 10. With DTR trigger signal output can be directly arduino pro mini ATMEGA328P and other Arduino board download traffic. Features: 1. Embedded USB transceiver, no external circuit device 2. Containing clock circuit, no external circuit device 3. Contains power-on reset circuit 4. The on-chip voltage regulator within the 3.3V output 5. Meet the USB2.0 specification requirements 6. SUSPEND pins support USB suspend state 7. Asynchronous serial data bus compatible with all handshakes and modulation controller interface signals 8. Support data format is 8 data bits, 1 stop bit and the parity bit 9. Connotation 512 byte receive buffer and 512 byte transmit buffer 10. Supports hardware or X-ON / X-OFF Handshake Package included: 2* CP2102 MICRO USB to UART TTL Module 6Pin Serial Converter STC Replace FT232 NEW.	B01I92B5W2 Price: $8.99 Score: 6.849 Category: Electronics Rating: 4 Votes: 1 Find similar products TOLAKO GPIO Module with Dual Channel Digital I/O Ports for Arduino. Package included: 1X GPIO Module.
B07DWNLSMG Price: $7.99 Score: 6.757 Category: Electronics Rating: 4.2 Votes: 91 Find similar products KEYESTUDIO 3.3V 2Pcs ESP8266 ESP-01 ESP01 WiFi Wireless Serial Transceiver Receiver Module Starter Kit for Arduino R3 Raspberry Pi Project. KEYESTUDIO- specialized in creating high quality, innovative, user-friendly open source hardware, such as micro-controllers, shields, sensors, display, learning kits, robotics and more for Arduin, Raspberry PI, STM32, 51, MICRO BIT etc. It is an ultra-low-power UART-WiFi pass-through module with industry-leading package size and ultra-low power technology. It is specially designed for mobile devices and IoT applications. It can connect users' physical devices to Wi-Fi wireless network for Internet or LAN communication, achieving the networking function. Features of Esp8266 WiFi Module : 1)Support wireless 802.11 b/g/n standard 2)Support three working modes: STA/AP/STA+AP 3)Built-in TCP/IP protocol stack to support multiple TCP Client connections 4)Support various Socket AT commands 5)Support UART/GPIO data communication interface 6)Support Smart Link intelligent networking function 7)Support remote firmware upgrade (OTA) 8)Built-in 32-bit MCU, able to double as an application processor 9)Ultra low consumption, suitable for battery powered applications. 10) 3.3V single power supply.	B09Y8PGMC7 Price: $19.99 Score: 6.667 Category: Electronics Rating: 4.8 Votes: 38 Find similar products AITRIP 5 PCS ESP8266 NodeMCU V3 CP2102 ESP-12F 4M Bytes Internet of Things WiFi Development Board Serial Wireless Module for Arduino IDE Micropython. Built-in Micro-USB, with flash and reset switches, easy to program Full I/O port and Wireless 802.11 supported, direct download no need to reset The chip model: CP2102; There is the way to guide you to use the new version: The command you needed to use is: esptool.py --baud 115200 --port /dev/tty.SLAB_USBtoUART write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1.7.bin 0x1000 user1.bin 0x37c000 esp_init_data_default.bin 0x37e000 blank.bin The important part is “—flash mode dio” https://github.com/espressif/esptool/wiki/SPI-Flash-Modes; Instruction & Steps of How to use: 1. Download the Compatible with Compatible with Arduino IDE, the latest version. 2. Install the IDE 3. Set up your Compatible with Compatible with Arduino IDE as: Go to File->Preferences and copy the URL below to get the ESP board manager extensions: http://arduino.esp8266.com/stable/package_esp8266com_index.json Placing the http:// before the URL lets the Compatible with Compatible with Arduino IDE use it...otherwise it gives you a protocol error. 4. Go to Tools > Board > Board Manager> Type esp8266 and download the Community esp8266 and install. 5. Set up your chip as: Tools -> Board -> NodeMCU 1.0 (ESP-12E Module) Tools -> Flash Size -> 4M (3M SPIFFS) Tools -> CPU Frequency -> 80 Mhz Tools -> Upload Speed -> 921600 Tools-->Port--> (whatever it is) 6. Download and run the 32 bit flasher exe at Github(Search for nodemcu/nodemcu-flasher/tree/master/ at Github) github.com/nodemcu/nodemcu-flasher/tree/master/Win32/Release Or download and run the 64 bit flasher exe at: github.com/nodemcu/nodemcu-flasher/tree/master/Win64/Release 7. In Compatible with Compatible with Arduino IDE, look for the old fashioned Blink program. Load, compile and upload. 8. Go to FILE> EXAMPLES> ESP8266> BLINK, it will start blinking. Package Including 5PCS * ESP8266 NodeMCU LUA CP2102 WiFi Wireless Development Board.
B08DD2G9D8 Price: $18.99 Score: 6.667 Category: Electronics Rating: 4.1 Votes: 51 Find similar products ACEIRMC Pro Micro for Atmega32U4 5V 16MHz Bootloadered IDE Micro USB Pro Micro Development Board Microcontroller Compatible for Pro Micro Serial Connection with arduino Pin Header (3pcs). Features: ATmega32U4 running at 5V/16MHz Supported under IDE v1.0.1 4 x 10-bit ADC pins, 12 x Digital I/Os Rx and Tx Hardware Serial Connections On-Board Micro-USB connector for programming Pay attention to : 1.The acceptable voltage range is 6 to 9 V 2.When you open the IDE software, could you please go to the tool and choose the board Explanation: 1. The Pro Micro is similar to the Pro mini except with a ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on board and do away with bulky external USB interface. 2. This tiny little board does all of the neat-o tricks that you're familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite -compatible boards but this little guy can go just about anywhere. If you're supplying unregulated power to the board, be sure to connect to the RAW pin on not VCC.	B0C3C3JZ2Q Price: $12.99 Score: 6.667 Category: Electronics Rating: 4.3 Votes: 246 Find similar products Mini Nano V3.0 ATmega328P Microcontroller Board w/USB Cable for Arduino. Note: Before running the procedure, pls install the corresponding computer system driver. Drivers: directly from the chip manufacturer: WCH 340 product home page: http://www.wch.cn/product/CH340.html http://www.wch.cn/download/CH341SER_LINUX_ZIP.html (linux should operate fine without the driver) http://www.wch.cn/download/CH341SER_MAC_ZIP.html http://www.wch-ic.com/download/list.asp?id=127 (windows) http://bit.ly/2pMF4in ATmega328 Microcontroller Microcontroller ATmega328P-AU Fully Compatible to Arduino Nano V3.0 ATmega328P-AU Input Voltage (recommended) 7V-12V;Input Voltage (limits) 6V-20V Bootloader installed, ready to upload sketches from Arduino software Analog Input Pins 8 Operating Voltage 5V DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Digital I/O Pins 14 (of which 6 provide PWM output) Flash Memory 32 KB (ATmega328) of which 2 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz Cable Length:245mm Dimention:Approx. 45x17x19mm Color:Blue(as the picture shows) Package: 1 x Nano V3.0 ATmega328P Arduino Compatible Board 1 x Mini USB Cable.