FantasticSearch | E-commerce Search Demo

Scroll to: Top Results

E-commerce Search Demo

AI Assisted Filters

Positive filters:

Negative filters:

Category filter:

Parameters

Query:

Positive filters:

Negative filters:

Category filters: All

AI Assist: ON

Page: 1

Products

Time taken: 3 Max score: 1000.000 Total hits: 100 Full time: 0.0 s
Showing 1-10 of 100 products

B09PH3GY82 Price: $21.99 Score: 1000.000 Category: Electronics Rating: 4.7 Votes: 15 Find similar products AITRIP 2PCS Pro Micro ATmega32U4 5V 16MHz Type-C Development Module Board with 2 Row pin Header Compatible arduino Leonardo Replace ATmega328 Pro Mini. Features: ATmega32U4 running at 5V/16MHz Recommend power supply for board: 6-7V, less than 9V On-Board Type-C connector for programming 4 x 10-bit ADC pins, 12 x Digital I/Os Rx and Tx Hardware Serial Connections How to use? 1. Connected to computer. (If this module cannot be recognized by your computer, please refer to this link to install the driver) 2. Opened Ard IDE and loaded Blink sketch. 3. Set board to Leonardo and selected the appropriate COM port (It showed up in the list already identified as a Leonardo). 4. Connected an LED to pin 9 and modified the sketch accordingly. 5. Hit upload and within a few seconds having a blinking LED. Package Includes: 2 x Pro Micro ATmega32U4 5V 16MHz Module ( Type-C).	B08RDDR5BB Price: $20.99 Score: 9.434 Category: Electronics Rating: 4.2 Votes: 10 Find similar products D-FLIFE ESP32 D1 Mini NodeMCU ESP-WROOM-32 WLAN WiFi Bluetooth IoT Development Board 5V Compatible with Arduino (3pcs). Energy saving The ESP32 is a chip designed with TSMC technology for extremely low power consumption (ultra-low power management), allowing for the best power and performance with its high efficiency. As the quiescent current of the ESP32 chip is less than 5 μA it is particularly suitable for use with batteries or rechargeable batteries Compatible It has a similar pin layout to the conventional D1 Mini ESP8266-12F and is therefore pin-compatible with most accessories for it. Parameter Power supply voltage (USB) 5V DC Input/Output voltage 3.3V DC Operating current min. 500mA CPU Xtensa single-dual-core 32-bit-LX6 RAM 512kB I/O Pins 34 ADC channels 18 ADC Resolution 12-bit DAC channels 2 DAC Resolution 8-bit Communications interfaces SPI, I2C, CAN, UART Max current drawn per GPIO pin 40mA WiFi protocols 802.11 b/g/n (802/11n up to 150 Mbps) Package： 3 * ESP32 D1 mini.
B0C3C3JZ2Q Price: $12.99 Score: 9.091 Category: Electronics Rating: 4.3 Votes: 246 Find similar products Mini Nano V3.0 ATmega328P Microcontroller Board w/USB Cable for Arduino. Note: Before running the procedure, pls install the corresponding computer system driver. Drivers: directly from the chip manufacturer: WCH 340 product home page: http://www.wch.cn/product/CH340.html http://www.wch.cn/download/CH341SER_LINUX_ZIP.html (linux should operate fine without the driver) http://www.wch.cn/download/CH341SER_MAC_ZIP.html http://www.wch-ic.com/download/list.asp?id=127 (windows) http://bit.ly/2pMF4in ATmega328 Microcontroller Microcontroller ATmega328P-AU Fully Compatible to Arduino Nano V3.0 ATmega328P-AU Input Voltage (recommended) 7V-12V;Input Voltage (limits) 6V-20V Bootloader installed, ready to upload sketches from Arduino software Analog Input Pins 8 Operating Voltage 5V DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Digital I/O Pins 14 (of which 6 provide PWM output) Flash Memory 32 KB (ATmega328) of which 2 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz Cable Length:245mm Dimention:Approx. 45x17x19mm Color:Blue(as the picture shows) Package: 1 x Nano V3.0 ATmega328P Arduino Compatible Board 1 x Mini USB Cable.	B08RWTF74S Price: $18.99 Score: 9.091 Category: Electronics Rating: 4.7 Votes: 23 Find similar products SNCT D1 Mini ESP8266 ESP-12 ESP-12F 4M Bytes CH340G CH340 V2 USB WeMos D1 Mini Compatible WiFi Development Board NodeMCU Lua IOT Board 3.3V with Pins (Pack of 5). .
B08DD2G9D8 Price: $18.99 Score: 8.929 Category: Electronics Rating: 4.1 Votes: 51 Find similar products ACEIRMC Pro Micro for Atmega32U4 5V 16MHz Bootloadered IDE Micro USB Pro Micro Development Board Microcontroller Compatible for Pro Micro Serial Connection with arduino Pin Header (3pcs). Features: ATmega32U4 running at 5V/16MHz Supported under IDE v1.0.1 4 x 10-bit ADC pins, 12 x Digital I/Os Rx and Tx Hardware Serial Connections On-Board Micro-USB connector for programming Pay attention to : 1.The acceptable voltage range is 6 to 9 V 2.When you open the IDE software, could you please go to the tool and choose the board Explanation: 1. The Pro Micro is similar to the Pro mini except with a ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on board and do away with bulky external USB interface. 2. This tiny little board does all of the neat-o tricks that you're familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite -compatible boards but this little guy can go just about anywhere. If you're supplying unregulated power to the board, be sure to connect to the RAW pin on not VCC.	B079BBVYZX Price: $36.99 Score: 8.929 Category: Electronics Rating: 4.5 Votes: 91 Find similar products [initeq] STM32 ARM STM32F103C8T6 Blue Pill Minimum System Development Board with ST-Link V2 USB Programmer (2-Pack + ST-Link V2). STM32F103C8T6 ARM STM32 Minimum System Development Board, commonly referred to as the Blue Pill board. Includes two development boards with male pin headers (not soldered) and one ST-Link V2 compatible USB device for programming/debugging. Powerful ARM Cortex MCU Microcontroller chip clocked at 72MHz Can be flashed with an Arduino-compatible bootloader. For details, search for stm32duino blue pill, also see stm32duino and mentions on HackadayIncludes ST-Link V2 programmer (random color and markings - most are gray, blue, brown/gold, or green).
B09Y8PGMC7 Price: $19.99 Score: 8.772 Category: Electronics Rating: 4.8 Votes: 38 Find similar products AITRIP 5 PCS ESP8266 NodeMCU V3 CP2102 ESP-12F 4M Bytes Internet of Things WiFi Development Board Serial Wireless Module for Arduino IDE Micropython. Built-in Micro-USB, with flash and reset switches, easy to program Full I/O port and Wireless 802.11 supported, direct download no need to reset The chip model: CP2102; There is the way to guide you to use the new version: The command you needed to use is: esptool.py --baud 115200 --port /dev/tty.SLAB_USBtoUART write_flash -fs 32m -ff 80m --flash_mode dio 0x00000 boot_v1.7.bin 0x1000 user1.bin 0x37c000 esp_init_data_default.bin 0x37e000 blank.bin The important part is “—flash mode dio” https://github.com/espressif/esptool/wiki/SPI-Flash-Modes; Instruction & Steps of How to use: 1. Download the Compatible with Compatible with Arduino IDE, the latest version. 2. Install the IDE 3. Set up your Compatible with Compatible with Arduino IDE as: Go to File->Preferences and copy the URL below to get the ESP board manager extensions: http://arduino.esp8266.com/stable/package_esp8266com_index.json Placing the http:// before the URL lets the Compatible with Compatible with Arduino IDE use it...otherwise it gives you a protocol error. 4. Go to Tools > Board > Board Manager> Type esp8266 and download the Community esp8266 and install. 5. Set up your chip as: Tools -> Board -> NodeMCU 1.0 (ESP-12E Module) Tools -> Flash Size -> 4M (3M SPIFFS) Tools -> CPU Frequency -> 80 Mhz Tools -> Upload Speed -> 921600 Tools-->Port--> (whatever it is) 6. Download and run the 32 bit flasher exe at Github(Search for nodemcu/nodemcu-flasher/tree/master/ at Github) github.com/nodemcu/nodemcu-flasher/tree/master/Win32/Release Or download and run the 64 bit flasher exe at: github.com/nodemcu/nodemcu-flasher/tree/master/Win64/Release 7. In Compatible with Compatible with Arduino IDE, look for the old fashioned Blink program. Load, compile and upload. 8. Go to FILE> EXAMPLES> ESP8266> BLINK, it will start blinking. Package Including 5PCS * ESP8266 NodeMCU LUA CP2102 WiFi Wireless Development Board.	B07XVYBR9Y Availability: Currently unavailable Score: 8.547 Category: Electronics Rating: 4.3 Votes: 59 Find similar products Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0. Input and OutputEach of the 14 digital pins on the Nano can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. Some pins have specialized functions:Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data. These pins are connected to the corresponding pins of the CH340G USB chip. The Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Nano 3.x). It has more or less the same functionality of the official UNO, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. You could download the driver of Nano V3.0 . ATTENTION: We dont have USB cables in this kit and you will need to buy a mini USB cable to use this NANO board. Package Include : 3 X Nano Board PCB Size: 18 x 45 mm Weight: 7 g.
B07R7X9S7W Availability: Currently unavailable Score: 8.403 Category: Electronics Rating: 5 Votes: 2 Find similar products LK COKOINO R3 Board Atmega328p Compatible with Arduino UNO REV3 with USB Cable. .	B004RF9LB8 Price: $10.95 Score: 8.264 Category: Electronics Rating: 4.4 Votes: 20 Find similar products SparkFun Pro Mini ATmega328-3.3V/8MHz Development Board Compatible with Arduino Boards and IDE. .